Blade Tip - Maximum reach of the blade from the center of the hub; Separates the leading and trailing edges.
Leading Edge (LE) - Edge of the blade that first cuts the water.
Trailing Edge (TE) - Edge from which the water exits the blade.
Blade Face (Pressure Side or Pitch Side) - Side of the blade facing toward you while viewing from the vessel’s stern.
Blade Back (Suction Side) - Side of the blade facing away from you while viewing from the vessel’s stern.
Blade Root (Fillet area) - The area where the blade attaches to the hub.
Hub - Solid cylinder located at the center of the propeller; Bored to accommodate the engine shaft; Hub shapes include cylindrical, conical, radius, & barreled.
Keyway - Slender rectangular slot broached into the interior of the hub; Helps to secure propeller to the shaft and prevent rotational slipping on the shaft
Cup - Small radius or curvature located at the trailing edge of blade; Cupping, helps to reduce or delay cavitation; Helps to reduce slip, thus increasing actual pitch and usable thrust.
Diameter - Defined as the maximum radius of one blade multiplied by 2; The diameter of the circle scribed by the blade tips as the propeller rotates General rules: Diameter usually increases as engine power increases and vice versa. (all other variables remaining constant)Diameter increases for slower boats and decreases for faster boats.
Pitch - (Theoretical definition) - The linear distance that the propeller would move in one complete revolution through a solid medium not allowing for slip. (Because under actual operating conditions slip occurs as propellers rotate absolute forward movement (actual pitch) is less than theoretical pitch) Different types of pitch are: 1. Constant (fixed) pitch - pitch is equal for each radius 2. Progressive pitch - pitch increases along the radial line from LE to TE 3. Variable pitch - pitch is different at selected radii 4. Controllable pitch - blade angle is mechanically varied
Pitch Angle (Not to be confused with pitch!) - Angle of the pressure face along the pitch line with respect to the plane of rotation measured in degrees. Pitch angle decreases from the blade root to the tip in order to maintain constant pitch.Pitch angle decreases from the blade root to the tip in order to maintain constant pitch. Relationship between Pitch & Pitch Angle Formula: Tan a = Pitch / 2Pr where: a = pitch angle and r = radius
Pitch Line - A line that passes through LE and TE of blade used as a reference for pitch angle
Propeller Center Line (PCL) - Linear reference line passing through hub center on the axis of propeller rotation.
Propeller Center Axis (PCA) - Linear reference line that locates the blade on the hub. Perpendicular to the PCL.
Blade Center Axis (BCA) - Linear reference line that indicates propeller rake.
Blade Center Line (BCL) - Reference line that intersects each cylindrical section at the midpoint of the blade section width. Indicates propeller skew
Rake - Propeller blade will slant forward or aft from the BCA. Positive rake ---> blade slants towards aft end of the hub. Negative rake --> blade slants towards forward end of the hub. Can be specified in inches at the tip or in degrees.
Skew - Blade Center Line is curvilinear sweeping back from the direction of rotation. Contour of the blade is not radially symmetrical about blade center axis
Track - Measurement of axial position of all blades with respect to each other
Rotation - Right hand propeller rotates clockwise when viewed from astern facing forward. Left hand propeller rotates counterclockwise when viewed astern facing forward. Twin screw applications utilize both LH (port side) and RH (starboard side) rotating propellers.
Blade Numbering - By convention the blade located at the position of the keyway is identified as Blade 1. The next blade in rotation is Blade 2 and so on.
Blade Sections - Referred to as Cylindrical Sections. Hub & fillet area account for about the first 20-30% of the sections
Blade Section Length & Stations - Section length is the same as blade width Each station is expressed as a percent of radius increment ( ie: 40 radius is 40% of the blade radius)
Blade Section Types - Ogival section - flat faced with symmetrically rounded back. Airfoil section - resemble traditional airplane wing sections. ie: rounded LE, max. thickness at about 1/3 length of blade aft of the LE. Supercavitating section - high speed application Sharp LE, max. thickness near TE.
Blade Thickness - A blade is thickest at the root for structural integrity. Within each radial section, the point of maximum thickness may not necessarily coincide with the midpoint of the chord length.
Blade Thickness Fraction (BTF) - Maximum blade design thickness as extended to the propeller center line / propeller diameter. Blades must have enough thickness to achieve desired sectional shape and provide sufficient strength under loading. Blades that are too thick produce less propeller efficiency.
Disc Area - Area of the circle scribed by propeller blade tips (P r2) where r = 1/2 diameter of the propeller
Projected Area Ratio (PAR) - Area of projected outline of propeller ÷ disc area; Smallest area ratio.
Developed Area Ratio (DAR) - Similar to PAR if pitch were 0; Area of blade rotated to 0 pitch ÷ disc area; Most widely used area ratio reference
Expanded Area Ratio (EAR) - Similar to DAR with sections "unwrapped" from hub; Largest area ratio
Camber - Often used but misunderstood. Defined as curvature in the mean thickness line of the blade section.
Cavitation - Cavitation is the phenomenon of water vaporizing or boiling due to the extreme decrease in pressure on the forward, or, suction side of the propeller blade. Cavitation can be caused by nicks in the leading edge, bent blades, too much cup, sharp corners at the leading edge, incorrect matching of propeller style to the vessel and engine or, simply, high vessel speed.
Ventilation - Sometimes the term cavitation is used when in reality ventilation is actually occurring. Ventilation is air from the water surface or exhaust gases being drawn into the propeller blades which causes the propeller to over rev and lose thrust. This is the effect that you sometimes feel when you are running in a following sea in rough weather.
Slip - The difference between the theoretical distance the propeller should travel in one revolution and the actual distance the vessel travels. For example if you cruise at 2000 rpm and your vessel has a 2:1 reduction gear, a wheel with 24" pitch, your theoretical speed through the water should be 19.74 knots (the distance a 24" wheel should move in one hour). In reality your vessel only does 14 knots at 2000 rpm on a calm day with no current, the difference is slip.